Technical Information
FILL CHART
| Wire Hider Raceway |
n/a |
n/a |
1/2 inch Series |
1 inch Series |
1-1/2 inch Series |
| Raceway On-A-Roll |
1/4 inch |
3/8 inch |
1/2 inch Series
|
1 inch Series |
1-1/2 inch Series |
| Cable / Wire Size |
Category/Designation |
40% |
40% |
20% |
40% |
20% |
40% |
20% |
40% |
|
Telephone
|
2-Pair, 24 AWG |
1 |
1 |
2 |
4 |
4 |
8 |
10 |
21 |
3-Pair, 24 AWG |
0 |
1 |
1 |
3 |
3 |
7 |
9 |
18 |
4-Pair, 24 AWG |
0 |
0 |
1 |
2 |
2 |
4 |
5 |
11 |
25-Pair, 24 AWG |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
2 |
|
Coaxial
|
RG58/U |
0 |
1 |
1 |
2 |
2 |
4 |
5 |
11 |
RG59/U |
0 |
0 |
0 |
1 |
1 |
2 |
3 |
7 |
RG62/U |
0 |
0 |
0 |
1 |
1 |
2 |
3 |
7 |
RG6/U |
0 |
0 |
0 |
1 |
1 |
2 |
2 |
5 |
| |
Twinaxial |
100 Ohm |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
3 |
| |
Shielded Twisted Pair
|
Type 1 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
3 |
Type 2 |
0 |
0 |
0 |
0 |
0 |
0 |
1 |
2 |
Type 3 |
0 |
0 |
0 |
1 |
1 |
2 |
3 |
8 |
| |
Fiber Optic
|
Two Strand (Duplex) "Multimode, 62.5/125um" |
0 |
1 |
1 |
2 |
2 |
4 |
5 |
11 |
PREMIERE MATERIALS AND PRODUCT DESCRIPTION
WIRE HIDER
Base Channel
|
Two Piece Raceway System with Flexible Flaps that grip wires/cables during installation
Mat'l: Rigid PVC UL94VO Flame Retatrdant listed material - UV Stabilized |
| 1/2 inch Series |
Inside Dimensions: 0.475 W x 0.474 H |
| 1 inch Series |
Inside Dimensions: 1.085 W x 0.545 H |
| 1-1/2 inch Series |
Inside Dimensions: 1.500 W x 0.687 H |
WIRE HIDER
Cover Lid
|
Rigid PVC UL94VO Flame Retardant listed material - UV Stabilized latex Paintable |
| 1/2 inch Series |
Outside Dimensions: 0.645 W x 0.535 H |
| 1 inch Series |
Outside Dimensions: 1.225 W x 0.605 H |
| 1-1/2 inch Series |
Outside Dimensions: 1.687 W x 0.875 H |
Raceway-On-A-Roll
|
Single Piece Raceway System manufactured in 50 ft and 100 ft Rolls
Mat'l: Rigid PVC UL94VO Flame Retardant listed material - UV Stabilized - latex paintable |
| 1/4 inch Series |
Inside Dimensions: 0.255 W x 0.125 H |
| 3/8 inch Series |
Inside Dimensions: 0.375 W x 0.375 H |
| 1/2 inch Series |
Inside Dimensions: 0.475 W x 0.474 H |
| 1 inch Series |
Inside Dimensions: 1.085 W x 0.545 H |
| 1-1/2 inch Series |
Inside Dimensions: 1.500 W x 0.687 H |
Cat 5 Accessories
|
Mat'l: ABS UL94VO/5A Flame Retardant listed material - UV Stabilized - latex paintable |
Accessories available for the following sizes: 1/2 inch, 1 inch and 1 1/2 inch Series
Accessories offered: Inside / Outside Corners - Right Angles - End Caps - Reducers - Surface Mount Box Adapters - Tee's
All accessories interface with all Wire Hider Raceway sizes and Raceway On-A-Roll 1/2"" and 1"" sizes
Important Notes:
All base raceway items supplied with adhesive foam tape on the bottom surface for positioning the raceway in place.
U.L. requires Mechanical fastening using the appropriate fastener inserted every 6 to 8 inches.
This chart is to be used as a guide for the referenced cable/wire size catagories. The end user will be responsible for
ensuring the fill rates do not exceed the recommended fill rate.
Premiere products are warranted to be free from defects in workmanship and materials, and it is understood that users will test them to determine use suitability. Premiere's only obligation will be to replace any defective product and not be liable for any loss or damage arising from the use or misuse of the product.
Copyright 2006 Premiere Raceway Products, Inc. Made in USA all rights reserved.
|
